Custom metal privacy screen - Art Deco Pilaster
  • Custom metal privacy screen - Art Deco Pilaster
  • Custom metal privacy screen - Art Deco Pilaster
  • Custom metal privacy screen - Art Deco Pilaster
  • Custom metal privacy screen - Art Deco Pilaster

Custom metal privacy screen - Art Deco Pilaster

Art deco pilaster privacy screen: fluted geometry

The art deco pilaster privacy screen creates a graphic separation without closing off your space. At the centre, a column of fine parallel stripes runs the full height, resembling a fluted pilaster. It widens in stages at mid-height and at the ends; on either side, interlocking diamonds and stepped frames compose a dense, straight-lined design.

Laser cut to your specifications and made in France, the panel is a single piece of sheet metal including its solid frame. It can dress up a fence, preserve a bit of privacy, or structure a room while letting light through. You choose the material, thickness, and size in the configurator: the pilaster then takes its place, without needing a capital.

Art Deco Pilaster: a fluted and geometric decorative metal screen

At the centre of the panel, fine parallel stripes form a continuous vertical column. This column widens in stages at mid-height and at the extremities, evoking the fluting of a classical pilaster. On each side, interlocking diamonds and stepped frames fill the space. The lines remain straight, and the solid frame surrounds the entire design.

The pattern is symmetrical from left to right. Its numerous openings and dense composition filter views while allowing air and light to circulate. The solid frame provides a clean border; the parallel lines produce a graphic shadow when light passes through. The design keeps its poise, even without an architecture degree.

This art deco screen joins our selection of garden panels to add relief to a fence or create a decorative screen in the garden.

Brushed stainless, raw steel, galva, aluminium or corten: choose your material

The material gives character to your art deco pilaster privacy screen and determines where it can be placed. For a large metal privacy screen, a slightly thicker gauge provides better stability depending on the chosen material.

MaterialAvailable thicknessesInstallation
Brushed stainless steel1 to 4 mmIndoor or outdoor
Raw steel2 to 20 mmPreferably indoor
Galvanised steel1 to 3 mmIndoor, or outdoor (1.5 mm minimum)
Anodised aluminium1.5 to 2 mmIndoor or outdoor
Corten steel1.5 mmOutdoors only

Brushed stainless steel offers a satin, luminous look and resists corrosion well. Raw steel retains its natural grey-black hue, while galvanised steel receives a zinc protection for a matte grey finish. Lightweight anodised aluminium does not rust.

A custom privacy screen tailored to your space

You choose the size in the configurator based on the opening you wish to dress. The proportions of the design are preserved: the fluted column remains centred and the stepped frames maintain their balance. A single panel can mark a separation; several pieces of the same size form a regular sequence along a fence.

Before configuring your art deco pilaster privacy screen, measure the available space and identify the planned fixing points. Consider the viewing distance: a panel seen from afar may require a stronger presence. The configurator blocks sizes that are too small for the chosen thickness, ensuring the fine lines and openings maintain proper structural integrity.

Your custom screen thus adjusts to your project. Have you already designed another pattern? You can upload your own DXF to have it laser cut.

Indoor or outdoor use: where to install it

Outdoors, this metal privacy screen can rhythm a fence, protect a dining area, or dress up a garden wall. Brushed stainless steel, anodised aluminium, and galvanised steel withstand rain in the appropriate thicknesses. In corten steel, the panel finds its place outdoors, for example against a brick wall or among plants.

Indoors, it visually separates an entrance from a living room, defines an office nook, or dresses a partition without completely blocking the light. Raw steel is well-suited for these uses with its natural grey-black appearance; brushed stainless steel and anodised aluminium provide a brighter finish.

Corten steel is for outdoors only. Its patina forms upon contact with the elements and can run off with rain, which would stain an indoor wall or floor. In the garden, its warm tones blend naturally with brick and vegetation.

Fixing and maintenance

The design does not include fixing holes. Installation is done via the frame onto posts, a chassis, a wall, or a pergola, using screws suited to the support and the weight of the panel. Supplied without accessories: screws, wall plugs, posts, and fixing brackets must be provided separately.

For routine maintenance, a slightly damp microfibre cloth is sufficient. On brushed stainless steel, use a suitable product and wipe in the direction of the brushing. Avoid abrasive sponges and chlorinated products, which can mark the surface. Corten patinates naturally outdoors and requires no special treatment.

For your art deco pilaster privacy screen, choose the material, thickness, and size, then click "Configure & buy". The pilaster is ready to stand guard, without getting too full of itself.

FAQ about the art deco pilaster privacy screen

Can the art deco pilaster privacy screen be used outdoors?

Yes, depending on the material. Brushed stainless steel and anodised aluminium withstand rain, as does galvanised steel in thicknesses suitable for outdoor use. Corten is reserved for outdoor use, where its patina can develop. Raw steel is primarily intended for indoors, as it can oxidise in humid air. The panel can thus dress a fence or structure a garden area.

Can corten steel be used indoors?

No. Corten develops a patina that continues to evolve and can run off with moisture. Indoors, it would risk staining walls and floors. This material is therefore for outdoors only, such as in a garden or on a facade. For an indoor separation, choose brushed stainless steel, anodised aluminium, or raw steel depending on the desired look.

What size should I choose for a screen panel?

The size is selected in the configurator, and the proportions of the pattern are maintained. Measure the space to be dressed, then consider what you wish to hide and the distance from which you will view the panel. To align several pieces, use an identical size to maintain a consistent rhythm. A cardboard template helps visualise the pilaster's position before ordering.

How do I fix a metal privacy screen?

The design does not feature fixing holes. The panel is mounted by its frame onto a suitable support, such as posts, a chassis, or a wall, using screws chosen according to the support and the weight of the piece. It is supplied without accessories: screws, plugs, posts, and brackets are not provided.

Brushed stainless or raw steel: which material to choose?

Brushed stainless steel (1 to 4 mm) offers a satin look and is suitable both inside and out. Raw steel (2 to 20 mm) provides a natural grey-black hue, better suited for indoors. Anodised aluminium (1.5 to 2 mm) is lightweight and does not rust. Corten (1.5 mm) develops a warm patina, but its use is for outdoors only.

Are galvanised steel or aluminium suitable for outdoors?

Yes, both materials can be suitable for outdoor use. Galvanised steel is protected by a zinc layer; a thickness of at least 1.5 mm is recommended outdoors. Anodised aluminium is lightweight and does not rust. For both options, check the available thicknesses in the configurator for your project and adapt the fixing to the chosen support.

How do I maintain a metal privacy screen?

A slightly damp microfibre cloth is generally enough to remove dust. For brushed stainless steel, use a suitable cleaner in the direction of the brushing. Avoid abrasive sponges and chlorinated products. Corten patinates naturally outdoors; this evolution is part of its appearance and requires no particular treatment.

Can I have my own design laser cut?

Yes. You can send your DXF file via john-steel.com to have it laser cut in the material and thickness of your choice. This is useful if your project requires a personal pattern or specific fixing holes within the design. The custom cutting service is available to both individuals and professionals.

Fast delivery

Delivery in 3 or 8 working days. Enjoy free shipping with the Boost option!*

Volume discounts

The more you buy, the more you save on your order.

Pay in 4 interest-free installments

Pay in 4 interest-free installments with PayPal on your orders.