Custom metal privacy screen - Art Deco Feathers
  • Custom metal privacy screen - Art Deco Feathers
  • Custom metal privacy screen - Art Deco Feathers
  • Custom metal privacy screen - Art Deco Feathers
  • Custom metal privacy screen - Art Deco Feathers

Custom metal privacy screen - Art Deco Feathers

Art deco feather privacy screen: a light fan-shaped design

An art deco feather privacy screen dresses your space with a fine and airy design. Small arrow-like points give rise to fans of slender lines, opening in arcs like peacock feathers. Stacked in staggered rows, they filter views while letting light flow through: a graphic presence that avoids the feel of an opaque wall.

This panel is laser cut to measure and made in France, crafted as a single piece of sheet metal including its frame. You choose the material, thickness, and size in the configurator. The pattern has a specific top and bottom: the points face downwards, a detail to keep in mind during installation.

Art Deco Feathers: fine and repeated fans

Across the entire height, fans of fine lines spring from small arrow points and open in arcs. Each row begins at the top of the previous one; this offset creates a continuous repetition without weighing down the panel. The numerous lines remain slender, giving the design its light appearance, like a succession of stylised feathers.

The pattern is symmetrical from left to right, but not from top to bottom. The points are oriented downwards, so you must respect the direction of the panel when installing it. This orientation contributes to the vertical rhythm of the rows. The gaps between the lines allow air and light to pass through, while the overall structure forms a decorative screen.

This decorative metal screen joins our selection of garden panels. Its fan design brings a delicate rhythm to a fence or a room divider, without turning your space into a literal feather duster.

Choose your material for your custom privacy screen

The material complements the finesse of the art deco feather privacy screen and determines where you can install it. For a large-scale metal screen, a slightly thicker gauge provides better stability, where available for the chosen material.

MaterialAvailable thicknessesInstallation location
Brushed stainless steel1 to 4 mmIndoor or outdoor
Raw steel2 to 20 mmPreferably indoor
Galvanised steel1 to 3 mmIndoor, or outdoor (1.5 mm minimum)
Anodised aluminium1.5 to 2 mmIndoor or outdoor
Corten steel1.5 mmOutdoors only

Brushed stainless steel offers a satin, luminous look that resists corrosion well. Raw steel keeps its natural grey-black hue for an industrial feel. Galvanised steel, protected by zinc, features a discreet matte grey. Anodised aluminium is lightweight and does not rust.

A custom privacy screen tailored to your space

Whether for a pergola opening, a section of fencing, or a room divider, you choose the size of your custom screen in the configurator. The proportions of the pattern are preserved so that the fans remain slender and the rows keep their rhythm. The configurator blocks dimensions that are too small for the selected thickness.

Before ordering your art deco feather privacy screen, measure the area to be dressed and consider the distance from which it will be viewed. For several panels side by side, choose the same size to extend the rows regularly. A marking with masking tape or a cardboard template helps to visualise their presence before installation.

Your screen thus adapts to the intended location, with its frame integrated into the piece. Do you want a different design or custom cut-outs? You can upload your own DXF to have it laser cut.

Indoor or outdoor: where to install your screen

Outdoors, this outdoor privacy screen can add rhythm to a fence, preserve the privacy of a dining area, or dress a garden wall. Brushed stainless steel, anodised aluminium, and galvanised steel are suitable for the exterior. The fan design allows air to circulate and punctuates the space with light lines, even when used as a shield.

Indoors, the panel creates an open-work separation between an entrance and a living room, or structures a space without blocking all the light. Raw steel fits perfectly here with its grey-black appearance. The arrangement of the fans draws the eye upwards; just remember to point the tips downwards during installation.

Corten steel is for outdoors only. Its patina forms progressively and can run with the rain; indoors, it would risk staining walls and floors. In the garden, its weathered tones blend beautifully with surrounding materials and vegetation.

Fixing and maintenance

The design does not include fixing holes. The piece is installed by its frame, on posts, a chassis, a wall, or a pergola, using screws suitable for the support and the weight of the panel. Supplied without accessories: screws, wall plugs, posts, and fixing brackets must be provided. Also, double-check the top-bottom orientation before fixing the panel.

For routine maintenance, a slightly damp microfibre cloth is sufficient. On brushed stainless steel, use a suitable cleaner in the direction of the brushing to revive the satin look. Corten patinates naturally outdoors and requires no special care. The numerous cut-outs can be dusted with a soft brush.

For your art deco feather privacy screen, choose the material, thickness, and size, then click on « Configure & buy ». The fans are ready to take flight.

FAQ about the art deco feather privacy screen

Is the art deco feather privacy screen suitable for outdoors?

Yes, depending on the material. Brushed stainless steel, anodised aluminium, and galvanised steel (minimum 1.5 mm) are suitable for outside. Corten is reserved for the exterior and patinates over time. Raw steel is better suited for indoors as it can oxidise in humid air. It is a great way to dress a fence or protect a terrace corner.

Can corten steel be installed indoors?

No. The corten patina forms through oxidation and can run with moisture. Indoors, it would risk staining walls, floors, or textiles. This material is therefore for outdoors only, where its patina can develop freely. For an indoor separation, brushed stainless steel, anodised aluminium, or raw steel are more appropriate options.

What size should I choose for this screen panel?

You select the size in the configurator, which maintains the design proportions to keep the fans looking elegant. Measure the area to be covered and consider the viewing distance. To align multiple pieces, keep the size identical so the rows extend harmoniously. A cardboard template is a handy way to check the effect before installation.

How do I fix the panel and respect its orientation?

The design has no fixing holes. The panel is fixed by its frame to posts, a chassis, or a wall using screws adapted to the support and weight. It is supplied without accessories: screws, plugs, and posts are not included. Respect the top-bottom direction during installation, as the arrow points must face downwards.

Which material should I choose for an open-work screen?

Brushed stainless steel (1 to 4 mm) works both inside and out with a luminous look. Raw steel (2 to 20 mm) has a grey-black finish, mainly for indoors. Anodised aluminium (1.5 to 2 mm) is light and rust-proof. Galvanised steel (1 to 3 mm) is zinc-protected, while corten (1.5 mm) is for outdoors only.

Galvanised or anodised aluminium for outdoor installation?

Both materials are suitable for the exterior. Galvanised steel is protected by a zinc layer and should be at least 1.5 mm for this use. Anodised aluminium is lightweight, does not rust, and is available from 1.5 to 2 mm. Your choice depends on the desired aesthetic and the fixing constraints of your panel.

How do I maintain the metal fan cut-outs?

A slightly damp microfibre cloth is enough for regular cleaning. The open-work areas can be dusted with a soft brush. For brushed stainless steel, use a specific cleaner and wipe in the direction of the grain. Corten patinates on its own outdoors. Avoid abrasive sponges and chlorinated products, which could mark certain surfaces.

Can I have my own design laser cut?

Yes, you can upload your DXF file to john-steel.com to have it laser cut in your chosen material and thickness. This is useful for creating a different pattern or planning specific fixing holes for your project. The file must describe the design to be cut; the size is then adjusted via the configurator.

Fast delivery

Delivery in 3 or 8 working days. Enjoy free shipping with the Boost option!*

Volume discounts

The more you buy, the more you save on your order.

Pay in 4 interest-free installments

Pay in 4 interest-free installments with PayPal on your orders.