Custom metal privacy screen - Art Deco Interlace
  • Custom metal privacy screen - Art Deco Interlace
  • Custom metal privacy screen - Art Deco Interlace
  • Custom metal privacy screen - Art Deco Interlace
  • Custom metal privacy screen - Art Deco Interlace

Custom metal privacy screen - Art Deco Interlace

Art deco interlace privacy screen: open and airy diamonds

The art deco interlace privacy screen plays with large open diamonds that overlap and intertwine across the entire height. Its fine, regular lines compose a geometric design that dresses up a garden, filters a view, or separates two spaces without closing them off. The generous openings let light and sight pass through: your privacy gains a bit of relief without making the landscape disappear.

Laser cut to your specifications and made in France, this panel consists of a single piece of sheet metal including its frame. You choose the material, thickness, and size in the configurator. Its left-to-right symmetry helps maintain a balanced look; however, when it comes to height, the pattern has a specific orientation.

Art Deco Interlace: a decorative metal screen design

Large open diamonds overlap and intertwine throughout the height, drawn with fine and regular lines. At the top, inverted chevrons fit together in the centre. Further down, the crossed lines extend the diamonds and create a continuous rhythm. At the bottom, vertical bars frame elongated diamonds. The frame surrounds the whole piece and keeps the design within a clean silhouette.

The pattern is symmetrical from left to right, but not from top to bottom: its orientation matters during installation. Its openings are large, making it one of the airiest panels in the series. This art deco interlace privacy screen filters the view rather than blocking it, while allowing air and light to circulate. A diamond-shaped shadow is a geometry that knows how to breathe.

This panel joins our selection of garden screen panels to create a decorative separation or to add rhythm to an outdoor space.

Brushed stainless, raw, galva, aluminium or corten: choose your material

The material gives character to your art deco interlace privacy screen and determines where you can install it. For a metal privacy screen with a large surface area, a slightly thicker gauge provides better stability, where available for the chosen material.

MaterialAvailable thicknessesWhere to install
Brushed stainless steel1 to 4 mmIndoors or outdoors
Raw steel2 to 20 mmPreferably indoors
Galvanised steel1 to 3 mmIndoors, or outdoors (1.5 mm minimum)
Anodised aluminium1.5 to 2 mmIndoors or outdoors
Corten steel1.5 mmOutdoors only

Brushed stainless steel offers a satin, luminous look that resists corrosion well. Raw steel retains the natural grey-black hue of the metal for an industrial feel. Galvanised steel, protected by its zinc layer, takes on a discreet matte grey. Anodised aluminium is lightweight, does not rust, and is easy to handle.

A custom privacy screen tailored to your space

A pergola opening, a section of fencing, or a partition between two rooms: every location has its own proportions. You specify the desired size in the configurator, and the proportions of the pattern are preserved so that the diamonds maintain their balance.

Before ordering your panel, measure the space to be dressed and consider the distance: seen from afar, a panel can seem smaller. To align several panels, use the same size to extend the lines regularly. The configurator rejects sizes that are too small for the chosen thickness; the interlace needs a bit of room to stay sharp.

Your custom privacy screen thus adapts to your project, and not the other way around. Have you designed another pattern? You can also upload your own DXF to have it laser cut.

Indoor or outdoor use: where to install it

Outdoors, this metal screen can protect a dining area from prying eyes, dress up a fence, or delimit a garden space. Brushed stainless steel, anodised aluminium, and galvanised steel withstand rain. An outdoor privacy screen in a courtyard or in front of a hedge maintains a filtered view thanks to its wide openings.

Indoors, the panel creates a light separation between two spaces, dresses up an entrance, or structures a living room without blocking all the light. Raw steel finds its place here with its natural grey-black finish.

Corten steel is for outdoors only, as its patina forms over time and can run off with the rain. It would stain walls and floors indoors. Outside, its warm tones blend beautifully with plants and garden materials.

Fixing and maintenance

The design does not include fixing holes: plan for installation via the frame, depending on your support (posts, chassis, wall, or pergola) and the weight of the panel, using suitable screws. Supplied without accessories: screws, wall plugs, posts, and fixing brackets are not provided. If your installation requires holes to be pre-cut, you can send your own file.

Maintenance is simple: a slightly damp microfibre cloth is usually enough. For stainless steel, a suitable cleaner applied in the direction of the brushing revives the shine. Corten patinates by itself outdoors; there is no need to plan a complicated routine for it.

For your art deco interlace privacy screen, choose the material, thickness, and size, then click on « Configure & buy ». The diamonds are just waiting for their spot.

FAQ about the art deco interlace privacy screen

Can the art deco interlace privacy screen be used outdoors?

Yes, depending on the material. Brushed stainless steel and anodised aluminium withstand rain, as does galvanised steel thanks to its zinc layer. Corten steel is reserved for the outdoors and patinates naturally. Raw steel is intended for indoors, as it oxidises in humid air. Its large openings filter the view without completely closing your space.

Can corten steel be used indoors?

No. The protective patina of corten continues to form and can run off with humidity. Indoors, it would risk staining walls, floors, and textiles. Corten is therefore for outdoors only, such as a garden, a facade, or a terrace. For a separation inside the home, prefer brushed stainless steel, anodised aluminium, or raw steel.

What size should I choose for a privacy screen?

The size is chosen in the configurator, which preserves the proportions of the pattern. Measure the space to be dressed and consider the distance from which you will view the panel. The large openings filter the view rather than blocking it; think about what you wish to hide. For several aligned panels, keeping the same size extends the interlace harmoniously.

How do I fix a metal privacy screen?

The design does not include fixing holes. Installation is planned via the frame, on posts, a chassis, or a wall, with screws suitable for the support and the weight of the piece. The panel is supplied without accessories: screws, plugs, posts, and brackets are not provided. Check the orientation of the pattern, which is symmetrical left-to-right but not top-to-bottom.

Brushed stainless or raw steel: which material to choose?

Brushed stainless steel (1 to 4 mm) has a satin look and is suitable both inside and out. Raw steel (2 to 20 mm) keeps a grey-black hue, mainly for indoors. Anodised aluminium (1.5 to 2 mm) is lightweight and does not rust. Corten (1.5 mm) develops a warm patina but remains exclusively for outdoor use.

Are galva or aluminium suitable for outdoors?

Yes. Galvanised steel is protected by a zinc layer; for outdoor use, a thickness of at least 1.5 mm is recommended. Anodised aluminium does not rust and is also suitable for rain. These two materials allow you to install the panel outside, considering the support and fixing. Corten is designed for the garden, while raw steel is reserved for the home.

How do I maintain a metal privacy screen?

A slightly damp microfibre cloth is generally enough to remove dust. For brushed stainless steel, a stainless steel cleaner applied in the direction of the brushing revives the satin look. Avoid abrasive sponges and chlorinated products, which can mark the surface. Corten patinates naturally outdoors and requires no particular cleaning to form its patina.

Can I have my own design laser cut?

Yes. You can send your DXF file via john-steel.com to have it laser cut in the material and thickness of your choice. This is useful for designing a matching panel or planning fixing holes adapted to your installation. Just ensure the drawing is usable and that the lines remain strong enough in the selected material.

Fast delivery

Delivery in 3 or 8 working days. Enjoy free shipping with the Boost option!*

Volume discounts

The more you buy, the more you save on your order.

Pay in 4 interest-free installments

Pay in 4 interest-free installments with PayPal on your orders.