Custom metal privacy screen - Art Deco Fan
  • Custom metal privacy screen - Art Deco Fan
  • Custom metal privacy screen - Art Deco Fan
  • Custom metal privacy screen - Art Deco Fan
  • Custom metal privacy screen - Art Deco Fan

Custom metal privacy screen - Art Deco Fan

Art deco fan privacy screen: a geometric sun at the heart of your home

The art deco fan privacy screen focuses on a powerful centre: a diamond from which oblique rays emanate, like an open fan or a stylised sun. Surrounding this, vertical bands and small ladder-like bars frame the composition. The result evokes the grand facades of 1930s architecture.

It is laser cut to measure and made in France, as a single piece of sheet metal including its frame. You choose the material, thickness, and size in the configurator. A sun that shines even on grey days: that is already a great start.

Art Deco Fan: a radiating pattern with an openwork design

In the middle of the panel, a solid diamond serves as the point of origin. Beams of oblique lines spread out on either side, creating two fans. Above and below, vertical bands taper to a point, while the edges are punctuated by small horizontal ladder bars. A continuous frame closes the entire piece.

The pattern is symmetrical in both directions, allowing it to be installed in any orientation. Its denser central part blocks the view more effectively, while the top and bottom bands allow more light to pass through. This sun casts a very graphic ray-shaped shadow on the ground.

You will find other models in our garden panels section. This art deco screen forms a beautiful set with other designs from the same series.

Choose your decorative metal screen: stainless, raw steel, galva, aluminium or corten

Each material provides a different interpretation of the radiating pattern of your art deco fan privacy screen. Choose based on the location and the desired look. For a large metal privacy screen, a greater thickness provides more rigidity, where available for the chosen material.

MaterialAvailable thicknessesWhere to install
Brushed stainless steel1 to 4 mmIndoors or outdoors
Raw steel2 to 20 mmPreferably indoors
Galvanised steel1 to 3 mmIndoors, or outdoors (1.5 mm minimum)
Anodised aluminium1.5 to 2 mmIndoors or outdoors
Corten steel1.5 mmOutdoors only

Brushed stainless steel makes the rays shine and resists corrosion well. Raw steel draws them in grey-black for an industrial workshop feel. Galvanised steel remains understated in matte grey, protected by its zinc layer. Anodised aluminium is lightweight and does not rust.

A custom privacy screen tailored to your project

The size is selected in the configurator, and proportions are maintained: the diamond remains centred and the rays keep their angle. You can thus create a screen for a patio corner, a fence panel, or a room divider.

To properly size your art deco fan privacy screen, consider where the centre of the pattern will be: at eye level, the fan reaches its full impact. Think about the distance and the surrounding space. The configurator prevents sizes that are too small for the chosen thickness to ensure the bars remain sturdy.

Your custom privacy screen bends to your wishes, not the other way around. And if you have your own pattern, you can upload your own DXF.

Indoor or outdoor use: where to install it

Outdoors, this metal privacy screen can be placed on a fence, against a brick wall, or as a screen on a terrace. Brushed stainless steel, anodised aluminium, and galvanised steel withstand the elements. An outdoor privacy screen placed facing the setting sun reveals a stunning play of shadows.

Indoors, it separates an entrance from a living room, dresses up a bare wall, or hides a radiator without blocking the light. Raw steel and stainless steel are perfectly at home here.

Corten steel is reserved for outdoors only. Its rust patina forms over time and can run when it rains; indoors, it would stain walls and floors. In the garden, its copper tones give the Art Deco sun a particular warmth.

Fixing and maintenance

The design does not include fixing holes. The panel is fixed by its frame to posts, a chassis, or a wall, using screws suitable for the support and the weight. Supplied without accessories: screws, wall plugs, and posts must be provided by you.

For maintenance, a slightly damp microfibre cloth is sufficient. Brushed stainless steel should be cleaned with a suitable cleaner, following the direction of the brushing. Corten patinas on its own and requires no care.

For your art deco fan privacy screen, choose your material, thickness, and size, then click on « Configure & buy ». Your Art Deco Fan is waiting for you.

FAQ about the art deco fan privacy screen

Can the art deco fan privacy screen be used outdoors?

Yes, depending on the material. Brushed stainless steel and anodised aluminium withstand rain, as does galvanised steel thanks to its zinc layer. Corten steel is specifically designed for the outdoors and patinas there. Only raw steel should be kept indoors, as it oxidises in humid air. Your screen can thus decorate a fence, a terrace, or a garden wall.

Can corten steel be used indoors?

No. Corten protects itself with a layer of rust that forms continuously and can run with humidity. Indoors, it would stain walls, floors, and textiles. We reserve it for outdoors only, in the garden, on a facade, or a terrace. For the home, choose brushed stainless steel, anodised aluminium, or raw steel.

What size should I choose for a metal privacy screen?

You select the size in the configurator, and the pattern proportions are maintained. Preferably place the central diamond at eye level, measure the available space, and consider the distance. If you are installing several panels, keep the same size so the fans mirror each other. A cardboard template helps with visualisation.

How do I fix a metal privacy screen?

The design does not feature fixing holes. The panel is fixed by its frame onto posts, a chassis, or a wall, using screws adapted to the support and the weight of the piece. It is supplied without accessories: screws, wall plugs, and posts are not provided.

Brushed stainless or corten: which material to choose?

Brushed stainless steel (1 to 4 mm) works everywhere, inside and out, with a luminous look. Corten (1.5 mm) takes on a warm patina, reserved for outdoors only. Anodised aluminium (1.5 to 2 mm) is lightweight and does not rust. Raw steel (2 to 20 mm) provides a dark, industrial finish, mostly for indoors.

Does galvanised steel rust outdoors?

Its zinc layer protects it from red rust for a long time. Over time, it may dull or develop a light white patina, which is normal. For outdoor use, a thickness of at least 1.5 mm is recommended. It is a sober option for a fence screen with a matte grey finish.

How do I maintain a metal privacy screen?

A slightly damp microfibre cloth is usually enough. For brushed stainless steel, use a stainless steel cleaner in the direction of the brushing. Corten requires no care: it patinas by itself. Avoid abrasive sponges and chlorine products, which would mark the surface.

Can I have my own design cut?

Yes. You can send your DXF file via john-steel.com: it is laser cut in the material and thickness of your choice. This is useful for adding fixing holes or creating a matching panel. Bending services are also open to everyone, individuals and professionals alike, directly on the site.

Fast delivery

Delivery in 3 or 8 working days. Enjoy free shipping with the Boost option!*

Volume discounts

The more you buy, the more you save on your order.

Pay in 4 interest-free installments

Pay in 4 interest-free installments with PayPal on your orders.